Market situation and advantages of new scaffolding stamping parts

1. In the construction process of traditional scaffolding stamping parts, the steel pipe of the appropriate height must be selected first, but if a building has multiple storey heights, the steel pipe needs to be extended with butt fasteners, and the vertical rod and the horizontal rod are connected during the construction process. It is also connected by fasteners. Compared with the standard layer, there are two horizontal rods on a vertical pole, and two cross fasteners are needed. A fastener has four screws, that is, eight screws need to be tightened for construction. The speed is very slow, wasting labor. 2. The construction process of the new scaffolding stamping parts The new scaffolding mainly no longer needs fasteners. The fasteners are replaced by discs and bolts. The discs of the new scaffolding are stamped parts with 10 thicknesses, and the small bolts are cast steel parts. Just insert the plug directly into the faceplate during installation. The operation is very simple. A sleeve with a diameter of 57 and a length of 20 cm is welded under the new scaffolding pole, so that the socket can be directly connected when the layer is high. Yes, it is easy to operate and has strong versatility. Third, the advantages of new scaffolding stampings over traditional scaffolding 1. Installation is more convenient and faster: in use, you only need to insert the plugs at both ends of the crossbar into the corresponding taper holes on the vertical pole, and then tap it tightly. The speed of lap and disassembly and the quality of lap are beyond the reach of traditional scaffolding. The assembly and disassembly speed is 8-10 times that of fastener steel pipe scaffolding, and more than 2 times that of bowl-fastening scaffolding. Speed u200bu200bup the construction speed, advance the construction period of the project, and reduce the construction cost. 2. Large bearing capacity: the vertical crossing of the axis of the vertical pole and the axis of the horizontal pole of the new building formwork support frame has high accuracy and reasonable force properties. Therefore, the bearing capacity is large, the overall rigidity is large, and the overall stability is strong. Each pole is allowed to carry 16 tons. And the use of diagonal rods is much less than traditional scaffolding. 3. Reliable two-way self-locking ability: First, the locking function of the cross bar and the vertical bar at the connecting piece is realized and guaranteed by the design structure, which reduces the shortcomings of the traditional scaffolding by manual locking, and makes the personnel uncomfortable. The stability factor is minimized. 4. Cost saving: the use of new quick-release formwork supports can greatly shorten the construction period, reduce technical costs and construction costs, and the use time of construction equipment rental, and reduce various expenses. 4. Maintenance and maintenance of new scaffolding stamping parts 1. The new scaffolding stamping parts adopt hot-dip galvanizing process, which is anti-corrosion and rust-proof and has a service life of up to 20 years. For some products that have not been hot-dip galvanized, it is necessary to periodically stop the rust removal and anti-rust treatment of the scaffolding components. In areas with high humidity (greater than 75%), anti-rust paint should be painted once a year, and generally should be painted once every two years. . Fasteners should be oiled, and bolts should be galvanized to prevent rust. When there is no condition for galvanizing, it should be washed with kerosene after each use and coated with engine oil to prevent rust, which greatly increases the cost. 2. The used scaffold stamping parts (including structural parts) should be returned to the expenditure database and classified and stored in time. When stacking in the open air, the site should be level with good drainage, with supporting pads underneath and covered with thatch cloth, and accessories and parts should be stored indoors. All bent or deformed rods should be straightened first, and damaged components should be repaired before they can be put into storage, otherwise they should be replaced. 3. Stamping parts of tool scaffolding (such as portal frame, bridge frame, hanging basket, material receiving table) need to be repaired and maintained in time after removal, and supporting storage. 4. The fasteners, nuts, backing plates, bolts and other small accessories used in the scaffolding stamping parts are easy to lose. The extra parts should be recycled and stored in time when they are being erected, and they should be checked and accepted in time when they are removed. 5. Establish and complete the scaffolding tool materials receiving, recycling, introspection, and maintenance system, in accordance with the criteria of who uses, who maintains, and who manages, implement quota acquisition or lease methods to increase loss and loss. 5. New-type scaffolding stamping parts are market conditions. New-type building formwork support frame. This technical product has been promoted nationwide and has been applied in large, medium and small projects. The engineering effect can achieve the effect of fair-faced concrete without plastering, which can eradicate the common quality problem of unqualified concrete appearance. At present, the technical products have been applied to large groups such as MCC Jingtang (formerly MCC 22nd Metallurgical), China Railway 16th Bureau, Beijing Construction Engineering, China Construction Sixth Bureau, China Construction Eighth Bureau, Hebei Construction Industry and other large groups and exported to Angola, Romania, India, the Philippines, Bangladesh, Algeria, Libya and other countries have had very successful results, very good results, and obvious benefits. Related news: The characteristics of the main materials of stamping parts, the treatment of common problems of stamping parts, the characteristics of scaffolding stamping parts and the importance of inspections