Stamping hardware factories around Daliang-what are the key precautions for metal stamping processing operations?

Stamping hardware factories around Daliang-What are the key considerations for metal stamping processing operations [Hardware] 15 years of focus on stamping, 3 million production capacity per day, 19 strict quality inspections, silk-like stamping accuracy, 1 to 1 customized service for you Summarize a few points. 1. Check whether various equipment and materials are properly prepared. 2. Operators and mold repairers are strictly prohibited from reaching into the mold during production. 3. When installing the suction fan, the operator is strictly forbidden to reach out to the motor to clean up waste. 4. It is strictly forbidden to wear slippers when going to work, so as not to hit your feet with molds and iron blocks in the workshop. Squad leaders, fitters, and mold repairers must wear protective shoes when they go to work; 5. Male operators are strictly prohibited from wearing long hair, and female operators must tie up their long hair to prevent long hair from getting caught in the flywheel. 6. Pay attention to fire prevention for other oils such as white electric oil, alcohol, cleaning agent and so on. 7. When packing materials, scraps and molds, you must wear gloves to avoid scratching your hands. 8. When there is oil, it must be cleaned up in time to avoid slipping and falling. 9. It is strictly forbidden to wear gloves when drilling and milling machines; when using the grinder, wear a mask and eye protection to protect yourself. 10. Pay attention to drag the mold to prevent it from falling on the ground (the flatbed cart must be lowered to pull the mold). 11. It is strictly forbidden for non-electricians to connect to electricity and repair the machine. 12. It is strictly forbidden to blow the air gun at people, which can easily hurt the eyes. 13. The operator needs to wear earplugs. 14. When the machine is found to be abnormal, turn off the power first and then find the technician on duty to deal with it in time. It is not allowed to deal with it without authorization. 15. When a new employee goes to work on the first day, the team leader must explain to him the safety operation rules and learn the safety operation rules once a week. 16. When adjusting the machine, be sure to adjust the machine to single-acting, and it is strictly forbidden to hit the continuous discharge belt. 17. Do not store any flammable or explosive materials under the switch. 18. Operators are strictly prohibited from chasing, chasing and hitting in the workshop to avoid falling, knocking over the product or hurting themselves. 19. Carry out the equipment inspection in accordance with the inspection content on the equipment check card, paying special attention to whether the guiding and braking devices of the punch press are operating normally, and the functions of single punching and continuous punching are distinct. 20. When installing the mold on the small punch, first loosen the locking device of the guide rail, install the upper and lower molds, and then adjust the guide rail stroke until it meets the requirements and lock the fastening device. In addition, when the high punch is placed on the mold, the order must be hit. Stroke stroke, after locking the upper mold, the lower mold is locked after hydraulic clamping, and check again before production. ·21. When discharging or manually feeding and picking the blanks individually, special tools (pliers, hooks) must be used, and it is strictly forbidden to send or pick up the blanks by hand. A single switch will hurt your hands, but a double switch. The machine must not leak oil, otherwise it will fall off. Do not expose the power supply, which is dangerous. 22. Wear gloves and concentrate when punching iron sheets, otherwise you will hurt your hands. 23. During work, first check whether there are any abnormalities in the operation of the equipment, such as unclear orders, continuous flushing, poor operation or electrical faults, immediately shut down and ask the technician on duty to deal with it. 24. It is strictly forbidden to use the foot switch for the punch, and all the original equipment of the machine should be removed. 25. When cleaning and inspecting the equipment, the power supply must be cut off before operation. 26. Cut off the power, clean and scrub the work surface, remove the mold for maintenance and storage, and check the lubrication system oil at a certain time every week. The small stamping hardware factory around Daliang-what are the key considerations for the hardware stamping processing operation [Hardware] The workshop is 4,100 square meters, nearly 100 sets of imported equipment, 39 design and R u0026 D team, free design and free proofing. Need to know more consultation telephone: (same number on WeChat)